This article will provide information about abrasive blasting.
The article will give details on the following topics:
Abrasive blasting, employed across multiple sectors, finds various applications such as removing rust and oil, eliminating surface coatings like paint, stripping contaminants, preparing surfaces for painting or coating, improving metal surfaces and adhesion, and even carving stone.
This technique involves propelling abrasive material at a surface using a pressurized blasting application to clean, smooth, roughen, or shape it. Over 150 years old, abrasive blasting has evolved as a favored method for its efficiency and adaptability in diverse applications.
Commonly referred to as sandblasting, the process is also known as media blasting or grit blasting, reflecting the variety of materials and equipment utilized. Compared to methods such as sanding, wire brushing, or using harmful chemical strippers and solvents, abrasive blasting stands out for its cost-effectiveness and time efficiency.
Choosing the right abrasive materials is crucial for achieving the desired surface finish. The anchor pattern or etch profile created by the abrasive directly influences the adhesion of subsequent coatings. Thus, selecting suitable abrasive media is essential for optimal surface preparation and finishing.
The size, shape, hardness, and density of abrasive media significantly determine the eventual surface appearance.
Size: Larger particles leave deeper impressions compared to a similar quantity of smaller particles, especially with fewer strikes. To achieve the desired outcome, using the minimal amount of media is advisable. Abrasives are cataloged by mesh size, grit size, or in microns.
Mesh size, denoting the number of mesh lines per square inch on a sieve, commonly categorizes abrasive media size. A range typically indicates the particle size that will pass through or be retained by the sieve. Similar to mesh size, grit size refers to the count of abrasive particles passing or being retained at specific sieve measurements. Microns, a metric length unit, are also employed to indicate abrasive size.
Shape: The abrasive media shape impacts its cutting penetration on the surface. Four primary categories—angular, sub-angular, rounded, and round—affect the anchor profile. Angular media, with jagged edges, produce a higher etch, quickly remove rust, create sharper and deeper patterns, and offer a higher cleaning rate. Conversely, rounded or sub-rounded shapes are smoother, producing a uniform, dimpled surface. Examples include crushed glass and aluminum oxide as either angular or sub-angular, while glass beads fall under round. Garnet and plastic abrasives are predominantly sub-angular or sub-rounded with fewer sharp edges.
Hardness: The Mohs scale of mineral hardness evaluates abrasive toughness. Higher Mohs values signify tougher materials, with lower values indicating softer ones. For example, aluminum oxide has a Mohs hardness of 9, glass beads range from 5 to 6, while plastic abrasives range from 3 to 4.
Hard abrasives like aluminum oxide, garnet, silicon carbide, steel shot, steel grit, and glass beads create more profound profiles, making them effective for polishing metals, forming profiles, and removing rust, corrosion, and scale from hard materials.
Soft abrasives such as walnut shells, plastic media, corn cob media, baking soda, and wheat starch offer a finer polish, ideal for cleaning delicate surfaces. They effectively remove grease and light coatings without causing etching, pitting, or surface damage.
Density: The density of abrasive particles influences the profile depth. Denser particles influence a smaller surface area and undergo less deformation upon impact, absorbing less energy. Specific gravity commonly describes density, with higher values indicating denser particles. For instance, aluminum oxide has a specific gravity of 3.94 to 3.96, glass beads have a density of 2.5, and steel shot and grit range from 4.8 to 7.8.
Abrasive blast systems are extensively used for finishing machine parts and components. Whether using abrasive blast cabinets, wet abrasive blasting systems, or slurry blast cabinets, these systems effectively remove carbon deposits, oxides, and discolorations while preparing surfaces for coatings, plating, painting, and cosmetic treatments.
Equipment in abrasive blasting systems facilitates precise cleaning of parts such as stampings, dies, molds, castings, pistons, and valves. These systems proficiently remove heat treat scale, carbon deposits, slag, oxides, discoloration, minor machine burrs, paint, varnish, lacquer, and rust.
Surfaces can be crafted for plating, painting, anodizing, and enhancing coating adhesion through abrasive blasting. Furthermore, peening enhances fatigue resistance, the durability of components in corrosive conditions, and alleviates stress at welding points. The automotive, appliance, jewelry, and photography sectors thrive on the superior quality finishes produced by abrasive blasting.
Diverse media like aluminum oxide, plastic abrasives, glass beads, steel grit, ceramic media, and corn cob are used in abrasive blast cleaning. Each abrasive is selected for its capability to achieve desired finishes and cleaning results, tailored to specific process requirements.
In industrial finishing and surface preparation, choosing the right abrasive blast system is critical for achieving desired results in cleaning, coating, texturing, or restoring components. Different industries—from automotive and aerospace to manufacturing and metalworking—require specialized abrasive blasting equipment to efficiently handle various materials, contaminants, and project scales. Below is an authoritative overview of the most commonly used abrasive blast systems, outlining their features, applications, and advantages to help you select the optimal solution for your specific surface preparation or finishing needs.
Abrasive Blast Cabinets: Abrasive blast cabinets, also known as sandblasting cabinets, are enclosed workspaces designed for cleaning precision parts, dies, castings, valves, pistons, molds, and stampings with meticulous accuracy. These blast cabinets utilize either suction or pressure systems to control the flow of abrasive materials, such as aluminum oxide, glass beads, or silicon carbide. They help prevent media loss and minimize dust exposure, making them ideal for laboratories, workshops, and manufacturing facilities requiring efficient, continuous blasting for delicate or intricate components.
Wet Blast: Wet abrasive blasting, sometimes called vapor blasting, is a surface preparation technique that combines water with abrasive media. This method is highly effective for cleaning, deflashing, and descaling textured components while reducing dust and static interruption. Wet blasting is ideal for rust removal, graffiti cleaning, and preparing surfaces before applying finishes, coatings, or paints. The water component serves to cushion the abrasive impact, minimizing substrate erosion and delivering a uniform, polished surface—benefits crucial for automotive restoration, aerospace parts, and sensitive equipment refurbishment.
Slurry Blast: Slurry blast cabinets leverage advanced Proceco®-exclusive technology for wet blasting, mixing abrasive media with water for superior cleaning performance. Slurry blasting excels in removing mill scale, oxidation, grease, and paint quickly, producing finely textured surfaces on white metal, aluminum, stainless steel, and other alloys. It's frequently used in heavy machinery maintenance, marine restoration, and the manufacturing of critical-engineered parts where damage must be minimized and consistent finishes are essential. This system enhances operator safety by suppressing airborne dust.
Vacuum Blast: Vacuum blasting—often referred to as dustless blasting—uses a closed-loop suction system to both blast and collect the abrasives simultaneously. This dust extraction feature dramatically reduces environmental contamination, making vacuum blast machines perfect for on-site operations, lead paint abatement, hazardous coatings removal, and confined areas where cleanliness is paramount. Vacuum blasting systems maximize abrasive recycling, minimize clean-up time, and lower operating costs, providing a sustainable and eco-friendly alternative in industries with strict regulatory requirements.
Centrifugal Blast: Centrifugal blasting, also known as wheel blasting, operates via high-speed rotating wheel turbines to propel abrasive media against workpieces. This high-efficiency method delivers consistent, uniform cleaning and is favored for large-scale operations such as structural steel preparation, railcar refurbishing, foundry casting cleaning, and shipbuilding. The process provides excellent surface profile for paint or powder coating adhesion, improves throughput, and reduces overall finishing cycle times compared to traditional air or manual blasting.
Air Blast: Air blasting, the most versatile abrasive blasting method, utilizes compressed air to accelerate dry abrasive materials—such as garnet, steel grit, or walnut shells—against surfaces. This technique is widely used for surface cleaning, paint and rust removal, surface profiling, and etching. The flexibility of adjusting air pressure makes air blasting suitable for a wide range of substrates, from heavy steel to delicate glass, and for diverse projects in industrial maintenance, construction, and restoration. Air blast systems can be operated manually or with automated blasting nozzles for increased consistency and reduced labor.
Bristle Blast: Bristle blasting offers a distinctive mechanical alternative to traditional abrasive media, using a rotating tool embedded with steel wire bristles. This surface preparation method efficiently removes corrosion, mill scale, and surface contaminants without significant material loss. It's highly effective for cleaning weld seams, pipe exteriors, and corroded metal structures, delivering a profiled surface ready for immediate coating or inspection. Bristle blasting is increasingly favored in pipeline maintenance, ship repair, and petrochemical industries where surface integrity is vital.
Pencil Blast: Pencil blasting, or microblasting, is a precise technique using very fine abrasive powder (such as aluminum oxide or baking soda) blended with compressed air at high pressure and delivered through a narrow adjustable nozzle. It allows technicians to delicately remove scale, oxidation, or micro-contaminants from miniature or intricate components, such as printed circuit boards, jewelry, dental prosthetics, or aerospace sensors. Pencil blasting supports controlled, detailed cleaning and material conservation for specialized assembly and repair tasks.
When selecting the right abrasive blasting equipment for your project, it is crucial to consider factors such as the type of substrate, the desired surface profile, environmental regulations, operational efficiency, and safety standards. Modern abrasive blast systems are equipped with advanced dust collectors, reclaimers, and media recycling options, making them integral to industrial process lines aiming for longevity and consistent quality. By choosing a system tailored to your application—whether it’s heavy-duty mill scale removal, precision cleaning, coating preparation, or environmentally sensitive projects—you ensure optimal results, increased productivity, and compliance with industry best practices. Comprehensive knowledge of different abrasive blast systems empowers buyers and facility managers to make informed decisions for sourcing, evaluating, and purchasing the equipment that best fits operational demands.
By directing a stream of the abrasive particles against a part or a surface, abrasive blasters and sandblasters clean and prepare surfaces. Blast wheels, pressurized water, or compressed air propel the abrasive or blasting media. Blasting is done by degreasing, deburring, deflashing, descaling, stripping coatings, and surface preparation of products made of metal, wood, plastic, glass, or other materials. Specialized micro-blast or micro-jet equipment is available for applications requiring precise surface preparation, material removal, and finishing. In addition, the surface created by blasting is ideal for other coating processes like thermal spraying, painting, or plating.
Sandblasters and abrasive blasting equipment consist of several key components. The pressure generator, which uses crankshaft or plunger pumps, increases the pressure of the carrier. Abrasive material is fed from a hopper or tank to the blasting wheel or directly to a nozzle, cannon, head, or lance. Smaller workpieces are typically handled in blast cabinets, while larger items are processed in blast rooms. The dust collection and filtration system captures fine abrasive media and waste particles from the air. Additionally, the media separator or reclaimer removes undersized abrasive particles and coarse debris.
Key performance specifications for sandblasters and abrasive blasting equipment include several critical factors. Media flow refers to the rate at which abrasive grains enter the system. Blast pressure is the pressure of water or air used to create a jet or stream for directing abrasive particles. Abrasive linear speed measures the velocity of abrasive grains as they are projected from the blast disk or nozzle. The term "abrasive particle velocity" is mainly associated with blast wheel equipment.
Sandblasters and abrasive blasting equipment come in various sizes and configurations. Some tools can be mounted on a bench, pedestal, cart, hand truck, floor, or skid, while others are portable or can be used hands-free. Larger systems may be mounted on trailers or trucks for mobility to job sites, such as steel tanks, ship hulls, or building walls. Crawler or track-mounted machines can clean or roughen surfaces in a controlled, repeatable manner. These small vehicles use magnetic or vacuum-mounted feet to adhere to surfaces and have track-mounted jet cutter heads that navigate the surface.
Operators typically move sandblasters and abrasive blasting equipment across large, fixed surfaces to clean or prepare them. For smaller surfaces, workpieces are often loaded onto conveyors, tumblers, or spinners, or placed on gantries or rotating tables. Abrasive delivery can be automated and controlled with CNC controllers and PC interfaces, enhancing precision and efficiency in blasting operations.
One can employ various metal finishing techniques to guarantee the quality of metal parts produced for industrial and commercial applications. Tumble blasting is one of the most efficient processes for processing tiny components. Here are some important details about this worthwhile process.
Tumble blasting processes smaller metal items in batches using a wheel blasting system. Inside the tumble blaster cabinet, a flighted belt made of steel or rubber drives the parts under the blast wheel. These parts are continuously exposed to abrasive media delivered from a single compressed air nozzle. Tumble blasters typically have capacities ranging from 1.5 to 12 cubic feet. This method is designed to remove flashes and burrs that might be difficult to eliminate with traditional finishing techniques. The random tumbling action ensures that the entire surface of each part is uniformly treated.
The unique design of tumble blasters allows them to efficiently process small metal components. Most tumble blasters can effectively remove burrs as small as 0.01 inch in diameter. The process is highly customizable, with adjustments available for blast pressure, medium type, and cycle duration, typically completing most tasks in under 20 minutes. The relatively low rotating speed of the equipment ensures that delicate parts are not damaged while still achieving effective results.
Sandblasting uses compressed air to blast sand across a hard surface of the equipment to clean and smooth it out. The surface becomes bright and smooth as a result. Sand particles are accelerated and compressed at high pressure onto the surface using air compressors or sandblasting equipment.
Sandblasting is a proven method for prefinishing surfaces. It effectively removes rust, paint, and oxidation from materials. Additionally, it addresses casting defects, welding imperfections, and scratches, thereby improving the overall surface finish.
Sandblasting involves four key variables.
In the first step of sandblasting, sand is loaded into the chamber of the sandblasting machine from the top. Once the sand chamber is filled, the machine is connected to an air source, typically an air compressor.
The workpiece is positioned inside the sandblasting cabinet, which includes a clamping system suitable for securing the workpiece and an accessible door for easy loading and unloading.
With the workpiece in place, the compressor is activated to force sand through the nozzle at high pressure onto the workpiece. Both the sand flow and air pressure can be adjusted according to the requirements of the task.
High-pressure sand application smooths the workpiece's surface. The final surface finish depends on the characteristics and abrasiveness of the sand used.
The operation may occasionally be repeated to get a good surface smoothness. This repetition is required because of the amount of dust gathered in the dust collection container after the process.
Large equipment should be positioned in an open area before undergoing sandblasting with compressed air.
Sandblasting is effective at removing rust, paint, and oxidation from material surfaces. Additionally, it helps eliminate casting defects, welding imperfections, and scratches, thereby improving the overall surface finish.
The process begins by directing grit blast material at high speeds, ranging from 65 to 110 meters per second, into a grit blasting machine. This abrasive impact effectively cleans the surface by removing contaminants. Currently, grit blasting is a prominent method for surface preparation, with the grit blast media propelled by compressed air. This technique remains commonly used for cleaning metal frames.
During the sandblasting process, there is a risk of sand causing injury to the eyes and ears, as well as potential harm to the respiratory system from inhaling sand. To mitigate these risks, personal protective equipment (PPE) is essential. This includes a helmet, goggles, face mask, and protective suit to ensure safety and prevent injuries.
The compressor must always maintain adequate pressure to operate safely. Excessive pressure can sometimes cause the compressor to malfunction or even explode.
Proper storage of sand is crucial. Sand should be kept in a designated area to prevent it from being spread to other work areas, which could lead to workplace issues.
Regular maintenance is essential to keep the machine in good working condition. A poorly maintained machine may leak sand during operation and could potentially cause accidents. Ensuring the machine is well-maintained helps prevent such risks.
To effectively clean or treat metal surfaces, an abrasive blasting machine requires key equipment. This machine utilizes compressed air to propel abrasive particles onto the surface. The combination of compressed air and stationary abrasive particles, along with proper technical components and good practices, ensures an efficient cleaning process. Each component plays a crucial role in the overall effectiveness of the abrasive blasting system; any malfunction in one component can significantly reduce the system's performance.
Abrasive blasting is commonly used for cleaning steel substrates such as bridges, ships, and other large structures. It is highly effective in both enclosed and open systems. Enclosed systems range from manually-operated sandblasting cabinets, where the operator works outside the blast chamber, to large rooms accommodating one or more operators within the enclosure. These systems can be pre-built or customized with various automation features to meet specific production and treatment needs, whether the work is performed indoors or outdoors, manually or automatically. Abrasive blasting involves projecting abrasive particles at high speeds to clean or treat surfaces. The effectiveness of the process largely depends on the choice and quality of the equipment used.
Abrasive blasting methods are generally categorized into two types: suction blasting and pressure blasting. Suction blasting, often used in smaller machines, is ideal for light cleaning tasks and is commonly applied in blast cabinets with limited workspace. In contrast, pressure blasting systems, which can be used in both cabinets and blast rooms, are designed for more demanding cleaning applications. Pressure blasting involves using higher pressure to propel abrasive particles, making it suitable for tougher cleaning challenges.
An abrasive sandblasting nozzle operates by forcing abrasive particles from a non-pressurized container into a gun chamber through a suction mechanism, commonly referred to as "venturi." In a suction system, the blast gun typically includes two hoses—one for air and one for abrasives—along with a canister for storing the abrasive material. The blast gun features a gun body, hose connectors, and an air jet with a nozzle at the front. Compressed air flows through the air jet, creating a drawing effect that pulls abrasive material into the gun body via the abrasive hose and accelerates it through the nozzle.
Suction blasting generally delivers a lower velocity and surface impact—about one-fourth to one-third less—compared to pressure blasting. This makes suction blasting more suitable for light to medium-duty applications. It is commonly used for delicate metals requiring minor deburring, light shot peening, and thin scale removal without significant penetration of the base metal. For example, suction blasting is often used to finish automotive and aerospace components made from magnesium, titanium, and aluminum.
In contrast, pressure blast systems use a single hose to deliver both air and abrasives at high pressure and speed through the blast nozzle, resulting in a more aggressive surface impact.
Abrasive blasting serves a variety of purposes. It is well-known for cleaning and strengthening steel bridges and concrete structures by removing unwanted contaminants, enhancing component appearance, and eliminating defects such as burrs and flashing. Sandblasters and abrasive blasters have diverse applications: some machines are designed to deburr sharp edges, remove flashing, wash parts, or strip off unwanted coatings like heat-treat scale, while others refine, roughen, or clean surfaces. Machines using media like glass beads and metal shots burnish or peen surfaces, improving fatigue strength by applying residual compressive stress, which is why components like shafts and turbine blades are often peened or shot blasted.
Surface preparation involves preparing surfaces for coating materials. For example, steel can be quickly cleaned to remove old paint, corrosion, and other contaminants. Fresh steel can also be cleaned to eliminate mill scale accumulated during manufacturing. Another critical task is creating a surface profile, also known as "etch" or "roughness," which is the texture produced by abrasive particles colliding with the surface. Coating manufacturers often specify the required profile to ensure proper adhesion and performance of their coatings.
Blasting can also benefit other materials like steel, masonry, and fiberglass. For instance, blasting fiberglass removes the top layer of glaze to expose air bubbles (gelcoat). Advanced metals such as aluminum, titanium, and magnesium require both debris removal and surface profiling before coating. In the aerospace and aviation industries, newer, gentler abrasive media are used for blasting composites and high-tech materials. Low-pressure blasting with materials like plastic, wheat starch, and agricultural media is employed to remove degraded paint from aircraft, helicopters, vehicles, and boats.
Surface finishing through abrasive blasting focuses on enhancing a product's appearance and functionality rather than preparing it for coating. Common finishing procedures include deflashing and deburring of mold-formed parts, removing production imperfections, and improving aesthetics.
Metal foundries frequently use abrasive blasting to remove small burrs from cast parts produced via die casting, permanent mold casting, and sand casting. Blasting not only removes these burrs but also helps detect tiny flaws that might otherwise go unnoticed, which is particularly beneficial for aircraft maintenance facilities refurbishing airplane wheels.
Surface compression through abrasive blasting is crucial for extending the lifespan of high-stress components. Shot peening is a specialized abrasive blasting process that increases the fatigue strength of metal surfaces by bombarding them with high-velocity spherical balls. Common media for shot peening include steel, glass, and ceramic shots. This process compresses the surface, reducing operational stress and leading to greater durability of shot-peened components compared to those that are not peened.
The safest and most efficient method for preparing metal for polishing is using an abrasive blast room. These rooms are designed to collect and recycle abrasive materials, which helps save time, reduce costs, and minimize environmental impact.
Abrasive blasting is effective for removing mill scale, old paint, and rust, restoring or preparing metal components for repainting. This process creates an even texture across the surface, ensuring a consistent finish.
Abrasive blast rooms, also known as blast booths, are specialized environments where abrasive blast pots are used to clean and prepare metal surfaces. These rooms are equipped to collect used abrasive material and recycle it efficiently. A blast room typically features a recovery system that separates dust from usable abrasives, allowing for the reuse of high-quality materials.
Once collected, the leftover abrasive material is processed by a recovery system, which separates dust and contaminants from the clean abrasives, making them suitable for reuse. Utilizing a blast room not only helps in conserving abrasive materials but also offers significant cost savings by maximizing the use of reusable abrasives.
Blast Enclosure: This component prevents abrasive material from escaping into the open air, ensuring that all blasting operations remain contained within the enclosure.
Blasting System: This system includes pressurized air and abrasive materials. Operators control the flow of these materials using valves. Sandblasting booths are a common type of blasting system that allows for effective and controlled blasting.
Abrasive Recovery System: This system automatically collects spent abrasive material. The waste is swept or suctioned into a dust collector for further processing.
Dust Collector: The dust collector filters the air in the room, preventing particulate matter from escaping into the outside environment.
Recycling Station: This station sorts through the residual abrasive material, separating high-quality, reusable grit from fine dust and debris.
Abrasive blasting can be performed manually using specialized hoses and nozzles tailored to the project requirements. Alternatively, mechanical blasting rigs can operate automatically along rail systems for larger or continuous operations.
During abrasive blasting, unfinished items are cleaned of paint, mold, and rust, creating a smooth, even surface ideal for finishing. The abrasive and dust particles generated during the process fall to the floor.
After blasting, a recovery system collects the remaining abrasive material from the floor. Various recovery methods may be employed, including sweepers, moving walls, air jets, or moving floors, to gather the waste into a recycling system.
The collected mixture is then cleaned in the recycling system to remove fine particles and dust before being reintroduced into the blasting pot for reuse.
Abrasive blast rooms can be customized to meet specific needs. Options include manual blasting hoses, rail-mounted systems, and different types of recovery systems. Due to the wide range of customization options, there is no single standard design for blasting rooms.
Micro-abrasive blasting is an advanced form of sandblasting that uses a focused stream of air combined with an abrasive material. This technique applies a thin stream of abrasive to a small area of a larger material using nozzles that range in size from 0.25mm to 1.25mm.
This method can be performed manually or mechanically and is designed for highly specialized tasks, targeting areas as small as 1.3mm x 2.0mm. While automated systems have greatly advanced, manual micro-abrasive blasting has been in use for a long time.
Micro-abrasive blasting is increasingly used in the manufacturing of medical parts. As medical devices become smaller and more intricate, effective cleaning of small workpieces is crucial. This technique helps address minor flaws that could affect the performance and functionality of these devices.
In injection molding, micro-abrasive blasting is utilized to remove residue and graphite remnants from mold cavities. This method effectively cleans the cavities without damaging them, which is important for maintaining the quality of the finished products.
The technique is also beneficial for laser-machined molds by removing deposits left behind from precision etching, thereby ensuring the accuracy of the molds.
Micro-abrasive blasting is used to clean medical instruments and implantable devices such as pacemakers. It is also employed to remove silicon insulation and cleaning residue from device parts, preventing performance issues and extending the lifespan of the tools. This method offers high precision and reliability for these critical applications.
Abrasive blast systems offer several benefits for surface preparation applications.
Efficiency: Abrasive blasting is highly effective for preparing metal surfaces for coating, painting, or other finishing treatments. It provides quick results and eliminates the uncertainty often associated with alternative methods.
High-Quality Products: Blast systems effectively remove complex compounds and impurities from metal surfaces, ensuring a more secure bond for coatings. This enhances the overall quality of the finished product.
Damage Prevention: Blasting systems help ensure the durability of the workpiece by preventing corrosion and rust. They also offer long-term protection when used with paint or powder coating, even in harsh conditions.
Operator Safety: Abrasive blast systems eliminate the need for hazardous chemicals and toxic materials. The disposal of used blasting media typically does not harm the environment or contribute to overflowing landfills, making them safe for use in any facility.
Sandblast cabinets include systems or machinery and componentsfor projecting blast media against a part‘s surface to abrade, clean, or modify the surface. Sand, abrasive, metal shot, and other blast media are driven or propelled using pressurized water, compressed air, or a blast wheel...
Sandblasting equipment includes systems or machinery, and components for projecting blast media against a part‘s surface to abrade, clean, or modify the surface. Sand, abrasive, metal shot, and other blast media are driven or propelled using pressurized water, compressed air, or a blast wheel...
Shot peening equipment includes systems or machinery and components for projecting shot peening media against a part‘s surface to modify the surface or surface engineer the part...
An aqueous part washer is an automated or semi-automated machine manufactured to clean, remove tough grease, and dry large or small parts before distribution or surface treatment. The washing is necessary since...
Automated parts washers are mechanical devices designed to efficiently remove grit, oil, grime, dirt, paint and other contaminating substances from parts with minimum manual supervision. These substances are removed...
Deburring is a secondary operation of a machining process that enhances the final quality of the product by removing raised edges and unwanted pieces of material, known as burrs, left by the initial...
Finishing machines are machines used for metal finishing, which is the last stage of the metal fabrication process; the stage encompasses the use of machines in finishing the metal surface...
A parts cleaner is a cleaning device that uses various types of solvents, cleaning agents, and processes to remove grease, grime, and contaminating materials from manufactured parts prior to shipment or movement for further processing...
A parts washer is a mechanical device designed to remove grit, grime, oil, miscellaneous debris, dirt, paint, and other contaminating substances from parts in preparation for their use in assembly operations, packaging, or coating...
A tumbling machine is a durable deburring and metal-polishing machine designed for finishing large parts or batches of smaller parts. A tumbling machine is also known as a barreling machine or a mass-finishing...
An ultrasonic cleaner is a type of sonic cleaner or sonic cleaning machine that uses cavitation to remove unwanted material. The cleaning effect is created by the compression and refraction of a cleaning medium. Miniscule vibrations propagate throughout the...
Ultrasonic cleaning is a type of cleaning process which uses cavitation induced by alternating compression and rarefaction cycles at ultrasonic frequencies. Ultrasonic frequencies are sound waves vibrating at 20 kHz or higher...
Vibratory tumbler is the equipment used in a vibratory finishing process, one of the most common methods in mass finishing. But how does a vibratory tumbler work...
A wastewater evaporator is a method of removing water from water-based waste by converting the water in the waste to a vapor and leaving contaminants. The function of a wastewater evaporator is to reduce the volume of waste materials...
Parts washers are designed for cleaning, degreasing of equipment, and drying of mass quantities of small or large parts in preparation for surface treatment, assembly, inspection, or shipment...